AIM Motorsport 719-719 Extension Lead – 200 cm`s
AIM 719-719 male to female extension cable. Used to extend the original wiring harness, e.g. when fitting analogue sensors. Available in different lengths to suit your
£42.00
AIM Motorsport SmartyCam GP HD – 84 Degree Lens
The new AIM SmartyCam GP HD (Rev 2.2) has been designed for motorsport and is incredibly compact and robust. The professional on-board camera records in full 1280p HD video and can include all the technical information that will help you improve your performance. The camera is available in two versions: The 67° lens is preferred for closed-roof cars, as it
£960.00
AIM Motorsport SmartyCam GP HD Replacement Glass Kit – To suit 120 degree lens
A replacement outer lens to suit the AIM SmartyCam GP HD camera. Unless the bullet camera is protected behind a screen, the exposed lens can often be damaged by flying rocks and debris. The kit includes the glass outer lens and o-ring. 2 Lenses available; One which suits the 60, 67 & 84 degree camera and one to suit the 120 degree camera. Always
£30.00
AIM Motorsport SmartyCam GP HD Replacement Glass Kit – To suit 60, 67 & 84 degree lens
A replacement outer lens to suit the AIM SmartyCam GP HD camera. Unless the bullet camera is protected behind a screen, the exposed lens can often be damaged by flying rocks and debris. The kit includes the glass outer lens and o-ring. 2 Lenses available; One which suits the 60, 67 & 84 degree camera and one to suit the 120 degree camera. Always
£30.00
AIM Motorsport SmartyCam HD – 84 Degree Lens
The AIM SmartyCam HD (Rev.2.1) camera has been designed for motorsport use, with the Rev 2.1 offering further improvements with better electronics/mechanics. The professional on-board camera records in full 1280p HD video and being incredibly compact and robust it is recommended for touring, GT and rally cars, as well as karts. Designed with a single
£840.00
AIM Motorsport GPS08 Module – To Suit Car or Bike – 2m Cable
GPS technology represents a true revolution in data acquisition. Thanks to the new AIM GPS08 Module and its GPS Manager software, you can immediately get lap times and all the data needed for improving your driving technique. The GPS module (antenna and receiver in one) is connected via a CAN cable and is both simple and quick to install in a number of
£264.00
AIM Motorsport Infrared Receiver – (4 Pin) 712 Metal Screw On Connecter to suit a Bike
The AIM Infrared Receiver (sometimes referred to as an Optical Lap Receiver), installed on a race car / bike or kart, receives the lap signal from the infrared transmitter. It is available with a 4-pin 712 (metal screw on) or a 4-pin 719 (plastic) connector and just needs to be pointed to the side of the track where the transmitter is installed and to
£84.00
AIM Motorsport Wheel Speed Sensor / Pick Up (Magnetic or Hall Effect Option) – Hall Effect – 712 Connection
The AIM wheel speed sensor / pick up is available in 2 versions. The Magnetic Wheel Speed Sensor is designed to be mounted using a bracket (not supplied) and to sense a trigger magnet (included) as it rotates past. Suitable mounting positions may include the wheel, wheel hub, prop shaft or brake disc. Cable length approximately 1.7m’s The Hall Effect
£72.00
AIM Motorsport Infrared Receiver – (4 Pin) 712 Metal Screw On Connecter to suit a Car
The AIM Infrared Receiver (sometimes referred to as an Optical Lap Receiver), installed on a race car / bike or kart, receives the lap signal from the infrared transmitter. It is available with a 4-pin 712 (metal screw on) or a 4-pin 719 (plastic) connector and just needs to be pointed to the side of the track where the transmitter is installed and to
£84.00
AIM Motorsport Wheel Speed Sensor / Pick Up (Magnetic or Hall Effect Option) – M12 Hall Speed Pick Up
The AIM wheel speed sensor / pick up is available in 2 versions. The Magnetic Wheel Speed Sensor is designed to be mounted using a bracket (not supplied) and to sense a trigger magnet (included) as it rotates past. Suitable mounting positions may include the wheel, wheel hub, prop shaft or brake disc. Cable length approximately 1.7m’s The Hall Effect
£72.00
AIM Motorsport Wheel Speed Sensor / Pick Up (Magnetic or Hall Effect Option) – Magnetic Speed Pick Up
The AIM wheel speed sensor / pick up is available in 2 versions. The Magnetic Wheel Speed Sensor is designed to be mounted using a bracket (not supplied) and to sense a trigger magnet (included) as it rotates past. Suitable mounting positions may include the wheel, wheel hub, prop shaft or brake disc. Cable length approximately 1.7m’s The Hall Effect
£72.00
AIM Motorsport Mounting Bracket To Suit Solo and Solo2 – Original bracket
The magnets on the back of the Solo unit make swapping between different vehicles a simple task, not forgetting that the Aim Solo uses GPS so doesn’t require any wires going to the unit. Available in three versions: Standard original mount ideal for use as a spare in a second car. Windscreen suction mount with a 90mm locking, quick release suction
£24.00
AIM Motorsport Mounting Bracket To Suit Solo and Solo2 – Windscreen Suction Mount
The magnets on the back of the Solo unit make swapping between different vehicles a simple task, not forgetting that the Aim Solo uses GPS so doesn’t require any wires going to the unit. Available in three versions: Standard original mount ideal for use as a spare in a second car. Windscreen suction mount with a 90mm locking, quick release suction
£66.00
AIM Motorsport SmartyCam GP HD – 67 Degree Standard Lens
The new AIM SmartyCam GP HD (Rev 2.2) has been designed for motorsport and is incredibly compact and robust. The professional on-board camera records in full 1280p HD video and can include all the technical information that will help you improve your performance. The camera is available in two versions: The 67° lens is preferred for closed-roof cars, as it
£960.00
AIM Motorsport Analogue Sensors – Steering Angle
Professional quality AIM Motorsport analogue sensors fitted with male 4 pin black 719 binder plug connections, to suit all AIM loggers and dash display / loggers. Oil or Fuel Pressure Sensor: 0-10 Bar. Available with a M10, 1/8 NPT or -3 JIC thread. Boost Pressure Sensor: 0-10 Bar. Available with a M10 thread. Oil / Water (Coolant) Temperature
£120.00
AIM Motorsport Analogue Sensors – Water / Oil Temperature Sensor, M10
Professional quality AIM Motorsport analogue sensors fitted with male 4 pin black 719 binder plug connections, to suit all AIM loggers and dash display / loggers. Oil or Fuel Pressure Sensor: 0-10 Bar. Available with a M10, 1/8 NPT or -3 JIC thread. Boost Pressure Sensor: 0-10 Bar. Available with a M10 thread. Oil / Water (Coolant) Temperature
£78.00
AIM Motorsport Analogue Sensors – Water / Oil Temperature Sensor, M5
Professional quality AIM Motorsport analogue sensors fitted with male 4 pin black 719 binder plug connections, to suit all AIM loggers and dash display / loggers. Oil or Fuel Pressure Sensor: 0-10 Bar. Available with a M10, 1/8 NPT or -3 JIC thread. Boost Pressure Sensor: 0-10 Bar. Available with a M10 thread. Oil / Water (Coolant) Temperature
£78.00
AIM Motorsport Data Hub / CAN Expansion – 2 Port with 40cm CAN Cable
The compact Data Hub, provides four additional CAN channels and works as an interface between the AIM Logger and its peripheral equipment / accessories (i.e. LCU-One Lambda Controller, GPS05 Module, TC Hub (thermocouples multiplier), MyChron Expansion, Memory Key and SmartyCam HD/GP HD cameras). The acquisition of all essential data you need to
£60.00
AIM Motorsport Analogue Sensors – Brake Pressure 0-100 Bar, -3 JIC
Professional quality AIM Motorsport analogue sensors fitted with male 4 pin black 719 binder plug connections, to suit all AIM loggers and dash display / loggers. Oil or Fuel Pressure Sensor: 0-10 Bar. Available with a M10, 1/8 NPT or -3 JIC thread. Boost Pressure Sensor: 0-10 Bar. Available with a M10 thread. Oil / Water (Coolant) Temperature
£180.00
AIM Motorsport Analogue Sensors – Brake Pressure 0-100 Bar, M10
Professional quality AIM Motorsport analogue sensors fitted with male 4 pin black 719 binder plug connections, to suit all AIM loggers and dash display / loggers. Oil or Fuel Pressure Sensor: 0-10 Bar. Available with a M10, 1/8 NPT or -3 JIC thread. Boost Pressure Sensor: 0-10 Bar. Available with a M10 thread. Oil / Water (Coolant) Temperature
£180.00